Meter readings checklist
3 min read
Part of: Rental inventory checklist
Short answer: a meter readings checklist should cover every meter in the property, not just electricity, and record each one’s location, serial number, every reading it shows and any balance, with a photograph where the numbers are legible. The serial matters as much as the reading, because a changed serial at check-out means the meter was replaced.
This meter readings checklist is for inventory clerks, agents, landlords and tenants on move-in or move-out day. It is part of our inventory checklist guide. Opening and closing readings divide one occupier’s bills from the next, and a reading that was never taken is very hard to reconstruct later.
Which meters should be checked?
Every meter that serves the property should be checked. An electricity reading should always be recorded, and the others checked for wherever they exist:
- Electricity: almost always present. Some show several rates and a total; cycle through the display and record each one.
- Gas: usually where there is a gas boiler or hob.
- Water: only some properties, often under the kitchen sink, in a utility cupboard or under a cover outside.
- Heat: common in new-build flats with communal heating, usually on the heat interface unit in a cupboard. Record the energy reading and the volume reading.
- Cooling: some flats with air conditioning have a separate meter, read like a heat meter.
- Smart meters and in-home displays: easy to walk past, and the reading is still needed.
What should a meter readings checklist record?
For each meter, the inventory should record:
- Where it is, in words someone else can follow, such as “communal cupboard on the second floor, opened with the FB1 key”.
- The serial number printed on the meter.
- Every register shown, one per line, with its units.
- Any credit, debt or emergency credit on a prepayment meter.
- A photograph of the serial and of each register, taken straight on so the digits can be read.
- If a meter cannot be found or reached, say so and why, rather than leaving it out.
Why does the serial number matter at check-out?
The serial number matters because it shows whether the meter at check-out is the same one recorded at check-in. If the serial is different, the meter was replaced during the tenancy, and the new meter’s low reading is not a mistake. A nearby identification tag often gives the old meter’s serial and final reading; photograph it.
What about communal and unlabelled meters?
Communal meter cupboards often hold rows of meters with no flat numbers. If the right one cannot be identified, photograph all of them, note that the meters are not clearly labelled, and record the flat number on any label nearby. Guessing at the right meter creates a bill dispute rather than settling one.
A meter reading takes seconds on the day and cannot be taken again once the next occupier moves in.
Key takeaways
- Record electricity every time, and check for gas, water, heat, cooling and smart meters.
- Write down the location, serial, every register and any balance.
- Photograph the serial and every register so the digits are legible.
- A different serial at check-out means a replaced meter.
Where InventorySafe fits
InventorySafe is a UK property inventory service whose clerks capture photos, video and voice notes at every visit and sign every report. Every meter is recorded with its location, serial, readings and balance, its photographs print beside it in the report, and the readings appear in the Report Preview emailed on the day.
Common questions
- Who should take meter readings when moving in?
- Anyone can, but it helps if the readings are in the check-in report, with photographs, because that record is dated and independent. The tenant should also give the readings to the energy and water suppliers if the bills are in their name.
- Do I need to read a smart meter when moving into a rental?
- Yes. A smart meter sends readings to the supplier, but a dated photograph of the reading on the day of the move is still the clearest record of where one occupier’s use ended and the next one’s began.
- What is a heat meter in a flat?
- A heat meter measures the heat a flat draws from a communal heating system. It usually shows an energy reading and a volume reading, and both should be recorded at check-in and check-out.
- What if the meter cupboard is locked?
- The report should say the meter could not be reached and why. Whoever manages the building, such as the agent or a concierge, can usually provide access so a reading can be taken.