Skip to content
← All articles
Check-ins

How to photograph meter readings

4 min read

Part of: What to photograph in each room

Short answer: photograph every meter so its serial number and every reading can be read, pressing through each screen of a digital meter and photographing each one. Add a wider shot showing where the meter is, and in a communal cupboard include the flat number beside it.

Knowing how to photograph meter readings properly saves a billing argument that otherwise has no answer. This checklist is for tenants taking their own readings on move-in or move-out day, landlords and agents between tenancies, and new clerks. It covers the photograph only; our post on meters and keys at check-in explains why the readings matter. It is part of our guide to what to photograph in each room.

How do you photograph a meter reading?

Work through this checklist for every meter in the property:

  • First, a wider shot showing where the meter is: the cupboard, the room, or the meter bank.
  • Then the serial number, close and sharp. It identifies the meter and shows at check-out whether it was replaced.
  • Then each reading. On a digital meter, press the display button and photograph every screen: each rate, the total, and any credit or balance.
  • On a heat or cooling meter, photograph both the energy reading in kWh and the volume in cubic metres.
  • On a prepayment meter, photograph the credit, any debt and any emergency credit shown.
  • In a communal cupboard, include the flat number on or beside the meter in the same frame.
  • Finally, note which key or fob opened the cupboard.

Which meters should you look for?

Look for every meter the property has, not just the obvious one. An electricity meter is almost always present and its reading is the one an inventory should never be without. Gas is present where there is a gas boiler or hob. Water meters are often under the kitchen sink, in a utility cupboard or under a cover in the pavement. A flat on a heat network usually has a heat meter at its heat interface unit, sometimes two. Smart meters are the ones most often missed, because the reading sits on a screen rather than a dial.

Why does a meter photograph come out unreadable?

Meter photographs often come out unreadable because meters sit in dark cupboards, behind glass, or above head height. Use the torch rather than the flash, which glares on the display, take the photograph square on, and check it on the screen before moving on. A meter photographed upside down or at an angle can make a digital display misleading, so make sure the labels on the unit read the right way up.

What if the meter has been replaced at check-out?

If the serial number at check-out does not match the check-in, the meter has been replaced during the tenancy. Look for the supplier’s tag left nearby, which usually shows the old serial and its final reading, and photograph it separately. Without that, a new meter’s low reading looks like an error.

Key takeaways

  • Photograph the serial and every reading so each can be read, including every screen of a digital meter.
  • Add a wider shot of the location, and the flat number in a communal cupboard.
  • Look for every meter, especially smart and heat meters.
  • Check each photograph is readable before moving on.

Where InventorySafe fits

InventorySafe is a UK property inventory service: clerks capture photos, video and voice notes at every visit, and each report is drafted with AI, with every observation citing a photograph, then reviewed and signed by the clerk. Every meter reading and balance is recorded with its location and serial number, and each meter is photographed in the report.

Common questions

Is a photo of the meter enough as a reading?
A clear photograph showing the serial number and every reading is usually the best record there is. Write the readings down as well and send them to the suppliers on the day you move in or out.
How do I read a smart meter?
Press the display button on the meter itself, not only the in-home display, and photograph each screen until it returns to the first. Each rate and any balance appears on its own screen.
Where is my water meter?
Commonly under the kitchen sink, in a utility cupboard, or under a small cover in the pavement outside. Some properties do not have one.
Why does a heat meter show two numbers?
A heat meter usually records the energy used, in kWh, and the volume of water that has passed through it, in cubic metres. Photograph both, because either may be used for billing.

See a report from one of your own properties.

Book a demo, or tell us where your portfolio is and we’ll confirm clerk coverage.

Book a demo

Request a booking

We’ll confirm availability and the final price by email.

1The visit
Type of report
Property size
Extra spaces · garage, loft, cloakroom… £10 each
0
2The property

3Your details