Skip to content
← All articles
Compliance

How to photograph smoke and CO alarms

4 min read

Part of: What to photograph in each room

Short answer: photograph every smoke, heat and carbon monoxide alarm on its own, close enough to read the replacement date, with a wider shot showing which room and floor it is on. For a carbon monoxide alarm, also photograph the appliance it covers, such as the boiler, so the record shows both are in the same room.

Knowing how to photograph smoke and carbon monoxide alarms gives a tenancy a dated record of fire safety on day one. This checklist is for landlords and agents before a tenancy starts, tenants checking alarms on move-in day, and new clerks. It is about the photographs; our post on smoke and carbon monoxide alarm rules explains the law. It is part of our guide to what to photograph in each room.

What do the alarm rules require in England?

In England, the Smoke and Carbon Monoxide Alarm (England) Regulations 2015, as amended from 1 October 2022, require a landlord to fit at least one smoke alarm on every storey used as living accommodation, and a carbon monoxide alarm in every room used as living accommodation that has a fixed combustion appliance, other than a gas cooker. Government guidance says the alarms must be working on the day a new tenancy begins. Wales and Scotland have their own, different rules.

How do you photograph an alarm?

Work through this checklist for every alarm in the property:

  • First, a wider shot showing where the alarm is: the ceiling of the hallway, the landing, the kitchen.
  • Then a close-up of the alarm, square on, so its type can be seen: smoke, heat or carbon monoxide.
  • Then the replacement or expiry date, legible. It is often printed on the side or the base, and may need the torch.
  • Then the test: hold the button and note the sound, and photograph the alarm’s light where it shows.
  • For a carbon monoxide alarm, a shot of the boiler, wood burner or other fixed appliance it covers.
  • For any alarm that is missing, a photograph of the empty ceiling plate or the place it should be.
  • For a damaged or partly removed alarm, a close-up that shows the problem.

How can you tell a smoke, heat and CO alarm apart?

A smoke alarm is usually a small white round unit with a test button. A heat alarm looks similar but is often recommended for kitchens, where smoke alarms give false alarms. A carbon monoxide alarm is usually an off-white rectangular box with carbon monoxide printed on it. The type matters, because a heat alarm on its own does not count as the smoke alarm for that floor.

What does an alarm test at check-in prove?

An alarm test at check-in proves the alarm had power and sounded on the day. It does not prove the system meets every regulation. Some mains-wired systems can only be properly tested by an electrician, so record what was seen and heard rather than claim a test that was not done. If the replacement date cannot be found, say so in the record.

Key takeaways

  • Photograph every alarm with its replacement date legible and its location shown.
  • Photograph a carbon monoxide alarm together with the appliance it covers.
  • Photograph where an alarm is missing, not just the ones that are there.
  • Record what the test showed, and never claim a test that was not possible.

Where InventorySafe fits

InventorySafe is a UK property inventory service: clerks capture photos, video and voice notes at every visit, and each report is drafted with AI, with every observation citing a photograph, then reviewed and signed by the clerk. Our clerks test and photograph smoke, heat and carbon monoxide alarms, flag any gap on the day, and can fit smoke and carbon monoxide alarms there and then if the property is not compliant.

Common questions

Where is the expiry date on a smoke alarm?
Usually on the side or the back of the alarm, sometimes on the base plate, printed as a replace-by date. If it cannot be read without removing the alarm, record that the date was not seen.
Does a gas cooker need a carbon monoxide alarm?
Not under the rules in England. Gas cookers are excluded, and the requirement applies to rooms with other fixed combustion appliances such as a gas boiler, a wood burner or an open fire.
Who tests the alarms during the tenancy?
Government guidance for England suggests tenants test their own alarms during the tenancy, replace the batteries if one is not working, and report it to the landlord if it still fails. The landlord must then repair or replace it.
Should I photograph an alarm I could not reach?
Yes. Photograph it from the floor and record that it was out of reach and not tested. That is a clearer record than leaving it out.

See a report from one of your own properties.

Book a demo, or tell us where your portfolio is and we’ll confirm clerk coverage.

Book a demo

Request a booking

We’ll confirm availability and the final price by email.

1The visit
Type of report
Property size
Extra spaces · garage, loft, cloakroom… £10 each
0
2The property

3Your details